AudioCodes Mediant Series Specifikace Strana 61
- Strana / 136
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Spectralink 84-Series with AudioCodes Gateway and Avaya Communication Manager: Interoperability Guide
1725-86914-000_C.docx
September 2013 61
15. TDM configuration
TDM Bus settings is used to configure the signal encoding used between the Mediant Gateway
and the PBX.
1 Select the Configuration tab and navigate to VOIP > TDM > TDM Bus Settings.
2 If your physical channel is T1 set PCM Law Select to MuLaw. For E1 set ALaw. Note
that there are very rare exceptions but this setting must match the configuration you
create on the PBX side.
3 Set TDM Bus Clock Source to Network
Note: Multiple Trunks
If you have multiple trunks please see Chapter 10: Expanding your System.
4 Click Submit.
- AudioCodes Gateway and 1
- Avaya Communication Manager 1
- Copyright Notice 2
- Warranty 2
- Contact Information 2
- Contents 3
- September 2013 4 4
- September 2013 5 5
- September 2013 6 6
- Introduction 7
- Product Support 8
- Spectralink References 8
- AudioCodes References 9
- Typography 12
- September 2013 13 13
- Chapter 1: Test Overview 14
- Network Topology 15
- 16
- Why Q.SIG? 17
- A Word about Wi-Fi 17
- September 2013 18 18
- September 2013 19 19
- SAS Emergency State 20
- User Authentication 20
- System Capacity Requirements 21
- Capacity Analysis 21
- September 2013 22 22
- September 2013 23 23
- Footnotes 24
- September 2013 25 25
- Package Contents 26
- T1/E1 Module 27
- CRMX Module 28
- Rear-Panel Description 29
- Insert the T1/E1 Module 30
- Connect to Power 31
- Connect to Computer 31
- Part II: Configuring the 32
- Components 32
- Mediant Gateway 33
- The Home screen 34
- The Burn button 34
- Navigation Pane 34
- The Search option 35
- Device Actions 35
- Verify License keys feature 35
- September 2013 36 36
- September 2013 37 37
- Disable the DHCP Client 38
- Set DHCP Lease Renewal 39
- September 2013 40 40
- Verify the settings 41
- September 2013 42 42
- 5. Set NTP settings 43
- 6. Set Syslog Parameters 44
- Set CDR Reporting 45
- September 2013 46 46
- 7. Enable SAS Application 47
- Configure SAS 48
- September 2013 49 49
- September 2013 50 50
- September 2013 51 51
- September 2013 52 52
- September 2013 53 53
- 4 Click Submit 54
- September 2013 55 55
- September 2013 56 56
- Avoiding a Routing Loop 57
- Detecting a routing loop 58
- September 2013 59 59
- 14. Enable Early Media 60
- 15. TDM configuration 61
- 16. B-Channel negotiation 62
- 17. Setting up the PRI 63
- September 2013 64 64
- September 2013 65 65
- Q931 Layer Response Behavior 66
- Set Call Rerouting 66
- September 2013 67 67
- 18. Changing the Password 68
- Gateway 69
- 19-inch Rack Mounting 70
- Cabling the Mediant 1000 72
- Connecting to E1/T1 Trunks 73
- Connecting to Power 74
- September 2013 75 75
- 1. Q.SIG 76
- September 2013 77 77
- September 2013 78 78
- September 2013 79 79
- September 2013 80 80
- 3 Press Esc-E to submit 81
- September 2013 82 82
- 4. Add a Trunk Group 83
- September 2013 84 84
- September 2013 85 85
- September 2013 86 86
- September 2013 87 87
- September 2013 88 88
- 5. Change Signaling Group 89
- 6. Set up Dialing Parameters 90
- 2 Add these parameters: 91
- 8. Add the Route Pattern 92
- 1. Add another DS1 94
- September 2013 95 95
- 3. Add a Trunk Group 96
- September 2013 97 97
- September 2013 98 98
- September 2013 99 99
- 1725-86914-000_C.docx 100
- September 2013 100 100
- 4. Change Signaling Group 101
- 5. Set up Dialing Parameters 102
- September 2013 103 103
- 7. Add the Route Pattern 104
- 8. Set Caller ID 104
- September 2013 105 105
- September 2013 106 106
- 1. Add the DS1 107
- 2. Add Signaling Group 107
- September 2013 108 108
- 3. Add Channels 109
- September 2013 110 110
- September 2013 111 111
- September 2013 112 112
- September 2013 113 113
- September 2013 114 114
- Troubleshooting 115
- PBX Functionality 116
- Chapter 12: Troubleshooting 117
- Caller ID 118
- Program a 10-digit Caller ID 118
- Clearing the configuration 119
- Manual method 119
- Software method 119
- September 2013 120 120
- Part IV: Appendices 121
- September 2013 122 122
- September 2013 123 123
- The software will load: 124
- The screen will display: 125
- September 2013 126 126
- Appendix C: Sample Files 127
- September 2013 128 128
- September 2013 129 129
- September 2013 130 130
- September 2013 131 131
- September 2013 132 132
- September 2013 133 133
- September 2013 134 134
- September 2013 135 135
- September 2013 136 136
Související produkty a manuály pro Brány / ovladače AudioCodes Mediant Series
(63 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce