AudioCodes Mediant 1000 Uživatelský manuál stáhnout pdf

5.6 - AudioCodes Mediant 1000 SIP Digital Gateway

1 Important Notes

• Check the SIP 3

Party Validation Website for current validation status. The

SIP 3

Part Validation Website can be viewed at:

http://testlab.inin.com or http://testlab.vonexus.com

• It is recommended to make basic changes to the I3 supplied .ini file then

utilize the web interface for further configuration.

• As this unit is a critical piece of the SIP infrastructure, it is highly

recommended that DHCP not be used. A static IP address is the preferred

method and is how the unit was configured during validation.

• After a factory reset, the Mediant 1000 will default to G.729 as its primary

codec

• Dial plan entries will supersede all proxy settings.

• The option for clock master is not exposed in the web interface. The settings

in the I3 supplied .ini file are to derive clock from the PSTN connection.

Should the internal oscillator be required, refer to INI Parameters Section of

this document, specifically the TDMBusClockSource, ClockMaster and

ClockMaster_x parameters.

• When using SRTP the number of available channels decreases by ~25%.

• Previous Issue resolved - With putback transfer: AudioCodes case # 13540.

•

Previous Issue resolved - FXO issue with TLS: AudioCodes case# 14031

2 Vendor Documentation

Documentation can be found on the CD shipped with the Mediant 1000.

3 Validated Firmware Version

5.60A.031.002

4 Install

Download the Mediant 1000 files from the 3

Party Validation website:

http://www.testlab.inin.com or http://www.testlab.vonexus.com

This document applies to one or more Interactive Intelligence and/or Vonexus

products.

Vonexus is a wholly owned subsidiary of Interactive

Intelligence.

1 2 3 4 5 6

Shrnutí obsahu

Strany 1 - 5.60A.031.002

5.6 - AudioCodes Mediant 1000 SIP Digital Gateway 1 Important Notes • Check the SIP 3rd Party Validation Website for current validation status

Strany 2 - 5 Configuration

Contained in the zip file will be the validated version of firmware (.cmp), as well as any supplemental configuration files, and a sample .ini file.

Strany 3

Figure 1 Figure 2 Changing the Configuration: • Prior to making any changes, the Audiocodes documentation should be consulted for informatio

Strany 4

3 (erase digits and relay using RFC2833) Example: DTMFTransportType = 3 RFC2833PayloadType Payload number to use for RFC2833 packets. This value is

Strany 5

6 Redundant Proxy Configuration The following configuration options are found under Protocol Management/Protocol Definition/Proxy & Registration

Strany 6 - 8 Security

7 Putback Transfer Select the Call Putback checkbox for the SIP line to enable the ability for the IC system to receive a call from the PSTN or a P

Další dokumenty pro Brány / ovladače AudioCodes Mediant 1000

Zobrazit dokument AudioCodes Mediant 1000 Uživatelský manuál

AudioCodes Mediant 1000 Uživatelský manuál (46 stránky)

Zobrazit dokument AudioCodes Mediant 1000 Instalační manuál

AudioCodes Mediant 1000 Instalační manuál (76 stránky)

Komentáře k této Příručce

Žádné komentáře

AudioCodes Mediant 1000 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Brány / ovladače AudioCodes Mediant 1000. AudioCodes Mediant 1000 SIP Digital Gateway 1 Important Uživatelská příručka

Shrnutí obsahu

Další dokumenty pro Brány / ovladače AudioCodes Mediant 1000

Komentáře k této Příručce

Související produkty a manuály pro Brány / ovladače AudioCodes Mediant 1000